Storage and storage solutions can sometimes be tricky.  Well at least for me they seem to be.  I hate building anything to store items only to find out a short time later that my storage needs have changed.  My thoughts on how to combat this was to have modular storage where not only the cabinets can be moved around easily as my needs change, but the cabinet themselves can be easily modified to fit different contents and make various items more accessible.  I had the idea to have cabinets that have 1″ in center dados cut and for most every shelf and divider to be sized to the nearest inch.  My hope is to be able to quickly and easily change my storage systems just as quickly as my needs and workflow seems to change.  With this being my first cabinet of this style, I would guess certain things will need to be tweaked over time.  If this can be even a starting point to ideal customizable storage I will be more than happy.  I guess only time will tell.

How to make a cabinet for sandpaper 01

I started off with cutting the sides, top and bottom to size.

How to make a cabinet for sandpaper 02

I like using the fence to reference of of when making repeat cuts.  you should use a spacer/stop block when using the fence and the miter gauge.  This keeps the wood from getting bound up between the fence and the blade.

How to make a cabinet for sandpaper 05a

How to make a cabinet for sandpaper 03

When cutting them down to final size, make sure to account for the thickness of the spacer block on the fence.

How to make a cabinet for sandpaper 04

 

How to make a cabinet for sandpaper 06

Once the four cabinet pieces were all cut I switched over to my dado blade set.

How to make a cabinet for sandpaper 07

With a sacrificial fence installed, I cut rabbets on both the top and bottom of each of the side pieces.

How to make a cabinet for sandpaper 08How to make a cabinet for sandpaper 09

Afte switching my dado blade set to 1/4″ wide, you can cut a groove along the back edge of each piece.  This will be for the back panel to come later.

How to make a cabinet for sandpaper 10How to make a cabinet for sandpaper 11

Again using the 1/4″ dado setup, I cut 1″ on center dados on the insides of both of the side components.  I also cut one dado in the center of the inside of both the top and bottom sections.

How to make a cabinet for sandpaper 12

I didn’t even bother changing to a standard blade to make the two cuts needed to get the back piece to final size.

How to make a cabinet for sandpaper 13

It’s always a good practice to test fit all the parts prior to adding glue to make sure everything fits as it should.  It is a lot easier to make any adjustments now rather than after glue is applied.

How to make a cabinet for sandpaper 14

How to make a cabinet for sandpaper 15I then applied glue to the joints and clamped one end into place.  Before clamping the opposite end, insert the back panel.

How to make a cabinet for sandpaper 16How to make a cabinet for sandpaper 17Once everything looks good and you can pre drill for 3 screws per joint and screws the screws in.  I used 2″ long screws for this step.

How to make a cabinet for sandpaper 18Then using the table saw I cut approximately 12 larger shelves and 6 smaller shelves to their final size.

How to make a cabinet for sandpaper 19Using one of the offcuts that was the same width as the large shelves, I created a quick jig to drill out some relief notches to make sandpaper easier to grab.

How to make a cabinet for sandpaper 20How to make a cabinet for sandpaper 21

Once the jig was clamp to my drill press table, a forstner bit made quick work of making the notches.

How to make a cabinet for sandpaper 22

A couple leftover pieces of plywood made great shelves in which to integrate dividers.  I cut a groove down the center of both sides along with rabbets on both ends so they fit into the 1/4″ dados cut in the sides earlier.

How to make a cabinet for sandpaper 23How to make a cabinet for sandpaper 24

A quick french cleat glued and screwed to the back of the cabinet made hanging it onto an existing french cleat on the wall super easy.  I planned on this being an end cabinet so I only notched the back of the cabinet on one side.  I you were to have the cabinet in the middle of the cleat, you would want to notch both sides.

How to make a cabinet for sandpaper 25

Sliding all of the shelf and divider components took less than 5 minutes.  With only one of the shelves needing to cut down approximately 1/16″ to fit.

How to make a cabinet for sandpaper 26

All said and done, I hope it keeps me from making too much of a mess of my sandpaper.  Thanks for checking it out!

3 Responses

  1. Ryan Rodlund

    Hey Nick! You build some pretty impressive stuff and I’ve certainly been binge watching. This sandpaper station is pretty handy but what was the overall dimension of the box?

    Reply

Leave a Reply to Ryan Rodlund Cancel reply