There are a lot of woodworking tools that are sometimes easier or more fun to make, rather than buy.  The marking knife is one of those tools because it is both fun and easy to make.  A marking knife can be as simple as a store bought utility knife or as complex as a damascus steel blade between unicorn tusk handles with exotic wood inlays finished in angel tears.Depending on how far you want to take it (or on your supply of unicorn tusk) it is a fun project none the less.  Whether you want to turn a knife handle on the lathe and use a store bought blade like I did here, or make the blade like I do in this project,  The possibilities are pretty much limitless.  This particular knife is pretty special to me.  The figured walnut gun stock blank came from a trip I took to my friend Braxton’s shop in Las Vegas and the knife itself was being made as a thank you gift for my friend Anthony for letting me stay at his place while I was in San Francisco.  They are both amazing at what they do and I highly suggest checking them out.  Let’s get on with the build!

Walnut Gun Stock Blank

This is the walnut gun stock blank I was going to be working with.  You can see I have already cut away and rounded a piece to be a lathe tool handle.  This is technically a reject for making gunstocks.  There were a couple knots and wormholes that didn’t make it worthy of being a gun stock.

 

Walnut Marking Knife1

The off-cut from the tool handle had some really nice figure to it and I decided to make the knife scales from it.

Walnut Marking Knife2

To clean up the sawn edge, I ran it past my jointer to give it a smooth surface.

Walnut Marking Knife3 Walnut Marking Knife4

For the blade I used O1 tool steel.  It was 1/8″ thick and 1″ wide.  I choose tool steel for it’s tight grain pattern.  I didn’t bother hardening or heat treating it.  It may dull a little quicker this way but will be really nice to sharpen or run across a leather strop.  I wiped it down with some brake cleaner to remove any dirt or grease.

Walnut Marking Knife6

I marked the steel at approximately 35° for the cutting angle and it’s overall length was just over 6″.

Walnut Marking Knife7

Using my angle grinder and a cut-off wheel, I cut the steel on the line.

Walnut Marking Knife8 Walnut Marking Knife9

I could then mark out the locations to drill the holes for the rivets and I used the bottom of the brake cleaner can to add a radius to the end of the knife steel.

Walnut Marking Knife10

Center punching the holes ensures the drill bit won’t wonder.  This is a home made center punch I made from an old metal tap.

Walnut Marking Knife11

Walnut Marking Knife12 Walnut Marking Knife13

A 1/8″ drill bit was used to make 2 through holes in the blade to accept the rivets.

Walnut Marking Knife14

To make sure the knife scales fit nice and flat against the steel, I ever so slightly de-burred the holes with a countersink bit.

Walnut Marking Knife15

A flap sander took away the bulk of the metal for what would be a 30° bevel on the cutting edge.

Walnut Marking Knife16

Taking it over to my slow speed grinder further refined the bevel.

Walnut Marking Knife17 Walnut Marking Knife18 Walnut Marking Knife19

I ground until there was a small burr along the entire length of the back of the bevel.

Walnut Marking Knife20 Walnut Marking Knife21 Walnut Marking Knife22 Walnut Marking Knife23 Walnut Marking Knife24 Walnut Marking Knife25

The bevel was further refined with wet stones, eventually bringing it to 8,000 grit.

Walnut Marking Knife26 Walnut Marking Knife27

Stropping it on a leather strop with some polishing compound brought it to razor sharp.

Walnut Marking Knife28

In this picture, I put the cut-off and the freshly polished piece side-by-side for comparison.

Walnut Marking Knife29

The slow speed grinder took care of the radius on the back as well.

Walnut Marking Knife30

I selected a certain part of the gun stock blank with the nicest looking grain purely for aesthetic reasons.

Walnut Marking Knife31

After marking the area I wanted, I cut it off on the bandsaw.

Walnut Marking Knife32

I brought the wood back to my jointer to clean up the marks left from the bandsaw.

Walnut Marking Knife34

I ended up with two book matched pieces that would most likely yield me 10 or more knife scale sets.

Walnut Marking Knife35

Walnut Marking Knife36

Then I cut two pairs to size on my table saw sled.  My original plan was to make two knives, but time restrictions allowed me to only make one.  So I decided on the set on the right because of the more unique grain pattern.

Walnut Marking Knife37

I could then use a 5/16″ brad point bit to counterbore the walnut to accept the head of the cutlers rivets.

Walnut Marking Knife38

A 5/32″ bit was used to make a through hole.  You could substitute an 1/8″ bit as well.

Walnut Marking Knife39

Using the same countersink bit I had used earlier, I put a very small chamfer on the hole that was to mate against the steel blade.  This was going to make certain there was no material to keep the wood and metal from sitting perfectly flat to one another.

Walnut Marking Knife40

Walnut Marking Knife41

Walnut Marking Knife42

Walnut Marking Knife43After a quick test fit, I applied epoxy to the walnut knife scales and sandwiched the blade in between.  A couple hammer blows set the rivet together permanently.

knife rivetsI choose solid nickel cutlers rivets as opposed to nickel plated ones.  This would allow me to sand the wood and metal flush later, and not worry about sanding through a thin layer of nickel plating.  Sometimes called fiction rivets, or push rivets, theses fasteners consist of a female socket, a male post, and are to be pressed or hammered together.  They do a really nice job keeping the knife together long term, as well as lining everything up and clamping things together while the epoxy cures.  They are also available in brass and come in several sizes.

 

Walnut Marking Knife45

Walnut Marking Knife46

Walnut Marking Knife47

Walnut Marking Knife48Some sanding on the belt sander and spindle sander brought the wood surface flush to the metal blade.

Walnut Marking Knife49I rounded the face of the knife handle as well as added a recess for a finger hold.

Walnut Marking Knife50A little bit of hand sanding ensured every little spot was nice and smooth.  I have been using this flexible backed sandpaper for a while know, and it does really well on these small projects with curves.

Walnut Marking Knife51

Walnut Marking Knife52

Walnut Marking Knife53

Walnut Marking Knife54

Walnut Marking Knife55A couple coats of danish oil brought out the beautiful figured grain and gave the finish a natural feel in the hand.

Walnut Marking Knife56When selecting the grain I was mindful of the edge grain as well.  I chose to orient the pieces so the grain created a bit of a chevron and pointed it towards the tip of the knife.  It seemed a lot more organic this way and had a nice flow to it.

Walnut Marking Knife57

 

Here it is sitting on my friend Anthony’s mill right after I gave it to him.

Walnut Marking Knife58And here is the finished knife.  The figured walnut and satin tool steel give it a really nice look and I am extremely pleased with final results.  Let me know what you think about it down below.  Thanks for taking the time to check it out!

 


Select list(s):


14 Responses

  1. Clay Baldwin

    Great marking knife but I don’t know whether I would use that beautiful walnut gunstock

    Reply
    • Nick

      to each their own – the blank was a reject for guns and was like $20 – well worth it to me

      Reply
    • Nick

      thanks much Dave – this walnut was amazing – makes it that much more fun to imagine the finished project come together

      Reply
    • Nick

      Always appreciated buddy – I’m pretty happy on how it turned out as well – thanks!

      Reply
  2. Nicholas Beukers

    hi Nick, I love the marking knife you should start selling them to your members, i’m sure they all want one.see you later Nick

    Reply
  3. Eric R

    Nice work Nick.
    That came out great.
    I really like making some of my tools, and I enjoy them all the more when I use them.
    Really enjoy your stuff man.
    Your videos, articles and the way you explain how you do some of your processes help the newer woodworkers to gain in confidence and experience.
    Thanks and keep it up.
    Eric

    Reply
    • Nick

      thanks Eric – I appreciate you saying so – glad I can help out and get people wanting to be in the shop!

      Reply
  4. Mike Mills

    Hey Nick… there is something about a really nice piece of walnot that can’t be beat. Rockler had some rustic and then some figured for awhile and i have a good amount in my shop. The depth and color are fantastic.

    Reply
    • Nick

      I agree – the richness and figure make a an awesome looking wood to work with

      Reply

Leave a Reply to Dave Winquist Cancel reply